Leave Your Message
China LKX-PV Series Surge Protector (SPD) for Solar and Wind Power - Reliable Suppliers & Factory Solutions
Hot Products

China LKX-PV Series Surge Protector (SPD) for Solar and Wind Power - Reliable Suppliers & Factory Solutions

The LKX-PV series surge protective devices (SPDs) are specially designed for new energy applications, including wind and solar power generation systems. With operating voltages of 500V, 800V, and 1000V, these high-quality protectors are essential for safeguarding your main DC power systems. They effectively protect against indirect and direct lightning currents, as well as other transient overvoltages. As a leading China supplier and factory, we are committed to providing reliable surge protection solutions tailored to enhance the safety and efficiency of your renewable energy installations

    01

    Model Meaning

    p1j36
    02

    Characteristics of the Product

    • Plug-in design Surge Protective Device (SPDs)
    • The visual window indicates the working status of the SPD, green(normal), red(replace)
    • Dual protection of hot melt overcurrent
    • Configure telecontrol interface to achieve remote control
    03

    Technical parameter details

    Product name 48V DC SPD 500V DC SPD 600V DC SPD 800V DC SPD 1000V DC SPD 1500V DC SPD
    Product model LKX-PV-48V LKX-PV-500V LKX-PV-600V LKX-PV-800V LKX-PV-1000V LKX-PV-1500V
    In (kA) 20 20 20 20 20 20
    Imax (kA) 40 40 40 40 40 40
    Up (kV) 1.0 2.5 3.2 3.6 4.0 5.2
    Response time (μs) 25 25 25 25 25 25
    Uc 48V 500V 600V 800V 1000V 1500V
    Operating temperature -40~+85℃ -40~+85℃ -40~+85℃ -40~+85℃ -40~+85℃ -40~+85℃
    04

    Outer appearance and installation dimensions

    p4zxh p5yhq p6q80 p7uzr
    05

    Installation considerations

    • Before installation, ensure power is disconnected. Operating while energized is strictly prohibited.
    • It is recommended to install a fuse or circuit breaker in series at the front end of the surge protection module.
    • Follow the installation diagram for connection during installation. DC+ is the positive pole, DC- is the negative pole, and PE is the ground wire. Avoid incorrect connections. After installation, close the circuit breaker (or fuse) switch and check if the operation status is normal.
    • After installation, insert the module into place and verify if the surge protection module is functioning correctly.
    • During use, regularly inspect the surge protection module and check the status of the fault display window. If the fault display window turns red or if the remote signaling terminal outputs an alarm signal, it indicates a malfunction of the surge protection module, which should be promptly repaired or replaced.
    • Parallel-connected power surge protection modules should be installed in parallel. The connection wires must be secure, reliable, short, thick, and straight.

    Frequently Asked Questions

    What do the green and red colors in the visual window of the SPD mean?
    The visual window indicates the real-time working status of the Surge Protective Device (SPD). Green indicates that the module is working normally, while red indicates that the module has faulted and needs to be replaced.
    What voltage options are available for the LKX-PV DC SPD series?
    The LKX-PV series offers multiple models to suit different DC system requirements, including 48V, 500V, 600V, 800V, 1000V, and 1500V DC options.
    What are the discharge current (In/Imax) ratings for these SPDs?
    Across all model variations, the nominal discharge current (In) is rated at 20 kA, and the maximum discharge current (Imax) is rated at 40 kA.
    What is the response time and operating temperature range for the device?
    The response time of these surge protective devices is extremely fast at ≤25 microseconds, and they are designed to operate reliably in temperatures ranging from -40°C to +85°C.
    How should the wiring be connected during installation?
    Connections must follow the installation diagram strictly: connect DC+ to the positive pole, DC- to the negative pole, and PE to the ground wire. Ensure that the power is disconnected before starting the installation.
    Why is it recommended to use a series fuse or circuit breaker with the SPD?
    Installing a fuse or circuit breaker in series at the front end provides an additional layer of protection, preventing potential hazards in the event of overcurrent or short-circuits during surge events.