0102030405
China Suppliers Factory Type 2 SPD Surge Protection Device 1000V DC 3P for High-Voltage Solar Systems
01
Model Meaning
02
Product principle and working conditions
- Meets ClassⅡ (8/20μs) SPD tests
- Based on zinc oxide technology
- Using 34S MOV, the maximum will be up to 8/20 μ s 40kA
- No power frequency continuous flow
- The operating environment temperature is -40°C~+80°C
- Remote signaling function is optional.
- When product falls, the green window turns to red and remote signaling provides remote alarm function
03
Technical parameter details
| Technical Data | ||||
|---|---|---|---|---|
| POLE | 3P | |||
| SPD Type | Type 2/ClassⅡ | |||
| Technology | MOV/MOV+GDT | |||
| Protection mode(s) | DC+PE.DC | |||
| Max.continuous operating voltage (D.c.) [Ucpv] | 800V | 1000V | 1200V | 1500V |
| Nominal discharge current(8/20μs) [In] | 20kA | |||
| Max.discharge current (8/20μs) [lmax] | 40kA | |||
| Protection level [Up] | ≤3.6kV | ≤4.0kV | ≤4.5kV | ≤5.2kV |
| Response time [tA] | ≤25ns | |||
| Admissible short-circuit current [lsccr] | 25kA | |||
| Max. backup fuse | 125AgL/Gg | |||
04
Mechanical Data
| Mechanical Data | ||||
|---|---|---|---|---|
| Current | AC system | |||
| SPD configuration | Single/Three phase | |||
| Pluggable | Available | |||
| Mounting | 35mm DIN rail | |||
| Housing material | Thermoplastic, UL 94 V-O | |||
| Operating temperature | -40℃...+80℃ | |||
| Protection rating | IP20 | |||
| Remote Signaling | Green/Red | |||
| Wiring for remote signaling | Optional | |||
| Max.Voltage/Current for remote signaling | Max 1.5mm solid/flexible | |||
| Standards compliance | 250V/0.1A; 125V/0.2A; 75V/0.5A | |||
| Certification | CE, CB, RoHS, TUV | |||
05
Outer appearance and installation dimensions
06
Installation considerations
- Verify complete power de-energization before commencing installation. Any work on active electrical systems is categorically prohibited.
- For optimal protection, incorporate series-connected overcurrent protection (fuse or breaker) preceding the surge suppression device.
- Installation wiring must strictly comply with the provided schematic: DC+ = Positive terminal, DC- = Negative terminal, PE = Protective earth ground. Ensure proper terminal identification to prevent wiring errors. Post-installation, energize the system by engaging the protective device (breaker/fuse) and confirm proper operational indicators.
- Finalize installation by securing the module in its designated location and performing functional validation of the surge protection system.
- Implement scheduled maintenance inspections including: Visual examination of the diagnostic indicator and verification of alarm contact status. Immediate replacement is mandatory upon detection of red fault indicator illumination or alarm signal activation.
- Parallel surge protection configurations require: True parallel circuit implementation, properly torqued connections, minimum-length conductors, adequate wire gauge (AWG), and direct routing without unnecessary bends.
Frequently Asked Questions (FAQ)
1. What is the maximum discharge current (Imax) of this SPD?
The maximum discharge current (8/20μs) for this Surge Protective Device is 40kA, utilizing high-performance 34S MOV technology.
2. How does the visual status indicator work?
Under normal operating conditions, the status indicator window displays green. If the device experiences a fault or degrades, the window turns red, indicating immediate replacement is required.
3. What mounting system is required for installation?
This device is designed for easy and secure installation on standard 35mm DIN rails, complying with standard electrical cabinet configurations.
4. Can this device operate in extreme temperature conditions?
Yes, the operating environment temperature range for this surge protective device is rated from -40°C up to +80°C.
5. What certifications does this product hold?
This product is fully certified and complies with international standards, holding CE, CB, RoHS, and TUV certifications.
